Tensile Modulus of Elasticity, psi 73°F 420,000 ASTM D638 Flexural Strength, psi 73°F 14,450 ASTM D790 ... Clean Room Materials Flammability Test N/A FM 4910 SCHEDULE 40 & 80 - DIMENSIONS Schedule 40 Dimensions ... Microsoft Word - PVC Pipe Specifications.doc Author:
Tensile Modulus - or Young's Modulus alt. Modulus of Elasticity - is a measure of stiffness of an elastic material. It is used to describe the elastic properties of objects like wires, rods or columns when they are stretched or compressed.
ented polyvinyl chloride (PVCO) pressure pipe has been installed in Europe since the early 1970s and in North America since 1991. MATERIAL PROPER TIES OF PVC PIPE COMPOUNDS Polyvinyl chloride pipe and fabricated fittings derive properties and characteristics from the properties of theirmaterial components.
Characteristics of PVC pipe PVC pipe is different from traditional piping materials. Understand ... Modulus ; of ; elasticity Maximum service temperature Tensile strength Maximum design stress Relative impact resistance ... Also, a visco-elastic material can more
Overview of materials for PVC, Extruded Categories: Polymer; Thermoplastic; Vinyl (PVC); PVC, Extruded. Material Notes: This property data is a summary of similar materials in the MatWeb database for the category "PVC, Extruded".
Unplasticized (Rigid) Polyvinyl Chloride (uPVC, PVC-U) UPVC is a thermoplastic, further classified as a polyvinyl plastic. It has a moderately low heat capacity among thermoplastics.
PVC-P is a thermoplastic, further classified as a polyvinyl plastic. It has a very low tensile strength and a moderately high ductility among thermoplastics. The graph bars on the material properties cards below compare PVC-P to: polyvinyl plastics (top), all thermoplastics (middle), and the entire database (bottom).
Polyvinyl chloride - Wikipedia, the free encyclopedia. The mechanical properties of rigid PVC (uPVC) are very good; the elastic modulus can .... Almost one third of plastic based medical devices are made from PVC.
NOTE: The information contained herein are typical values intended for reference and comparison purposes only.
Thermoplastic materials exhibit non-linear elastic behavior and are sensitive to rate of strain, temperature, and creep. Creep is a visco-elastic phenomenon where the strain in a material continues to increase with time when subjected to a constant load (Figure 3).
Physical Properties for PVC and CPVC Pipe( Schedule 40 and 80) Article Title: Physical Properties for PVC and CPVC Pipe( Schedule 40 and 80) Article Summary: Physical, Mechanical, Electrical and Thermal Typical Properties.
Material Notes: This property data is a summary of similar materials in the MatWeb database for the category "PVC, Extruded". Each property range of values reported is minimum and maximum values of appropriate MatWeb entries.
The modulus of elasticity of PVC pipes is a major advantage for buried applications, particularly where soil movement or vibration is anticipated.
View plastic materials found under a specific property group: Click on the tab of a specific property group. Sort plastic materials: Click the down or up arrows (triangles) or column headings to sort plastic materials or material properties. Compare plastic materials: Select two or more materials and then press "Compare Materials".
Elasticity and Creep PVC-O has a modulus of elasticity up to 24% higher than normal PVC-U in the oriented direction and a similar modulus to standard PVC-U in other directions. The elastic modulus of PVC-M is marginally lower than standard PVC-U.
Poly vinyl chloride ... 9 months had limited effects on the tensile strength and modulus of elasticity of ... material and the second is plastic behavior which can be ... Online Service] Overview of materials for PVC, Extruded - MatWeb
Modulus of Elasticity Young Modulus for some Common Materials. Young modulus is a description of the stiffness or elasticity of a material. It is a fundamental property that cannot be changed and is dependent on the current pressure and temperature of the sample.
Tensile modulus Fig.2 shows the comparison of tensile modulus of PVC products with other plastics. The tensile modulus is also known as the Young’s Modulus, which is expressed in terms of the ratio between the tensile stress per unit area of the cross section and the elongation in the direction of the tensile stress.
Chapter 3 Material Properties 43 Chapter 3 Material Properties Scope ... (PVC). These can be re-melted upon the application of heat. The solid state of thermoplastics is the result of physical forces that immobilize polymer chains and prevent them from slipping past each other. When heat is applied, these forces