8 ft board for a porch

WPC Decking Related

1 in. x 6 in. x 8 ft. Pine Board Pattern Tongue and Groove ...

1 in. x 12 in. x 8 ft. 1 in. x 12 in. x 8 ft. S1S2E Standard Band Sawn Eastern White Pine Board (3-Pieces Per Box) is the natural choice where warmth character and quality are preferred. This is a versatile rustic board with a variety of natural characteristics.

Get Quotes / Contact Us

Deck Calculator - Full Plans and Costs - Imperial

Enter cost per linear foot and wastage % for Stumps, Bearers, Joists and Boards to Calculate individual and Total Costs. Linear feet and cost are auto updated when the deck is re-calculated, with individual costs for stumps, bearers and joists displayed in each section.

Get Quotes / Contact Us

Tips for How to Build a Deck | The Family Handyman

The result is that end-to-end deck boards share the 1-1/2-in. thickness of each joist. That can cause problems, especially with wood decks. With only 3/4 in. of nailing surface, fasteners will cause ends to split, and since the board ends have to be tight, untreated wood will rot.

Get Quotes / Contact Us

How to Buy Deck Lumber - Family Handyman

The depths of joists can vary by as much as 3/8 in.; the 12-ft. long 2x10s at your lumberyard may measure 9-1/8 in. in depth, while the 16-footers measure 9-1/2 in. Deck boards secured to uneven joists will flex more and the fasteners will creak and pop.

Get Quotes / Contact Us

Composite Deck Board Dimensions | Seventrust

Composite Deck Profiles & Measurements. Little details, big difference. ... 1" Grooved Porch Floor Board Actual Face: .94 in x 4.5 in (24 mm x 114 mm) Actual Overall: .94 in x 4.5 in ... 1.625 in x 8 in x 9 ft (41 mm x 203 mm x 274 cm) 1.625 in x 8 in x 10 ft (41 mm x 203 mm x 304 cm)

Get Quotes / Contact Us

How to Build a Simple Deck | DIY Deck Building | This Old ...

Set up batter boards and mason's strings and determine footing locations at the deck's outside corners and at 8-foot intervals along the front rim joist. Mark each location, then temporarily remove the mason's strings.

Get Quotes / Contact Us

How Wide Should the Floor Joist Be for a Deck? | Home ...

Deck Framing. Decks are supported on 4-by-4-inch posts, one in each corner and at least one every 8 feet. The outside edge of the deck is constructed with a board the same width as your joists.

Get Quotes / Contact Us

How to Build an 8 x10 Deck for Beginners - YouTube

This video will cover the basics you will need to build an 8ft x 10ft outdoor treated deck/patio. ... pouring concrete footers,2x8 framing,4x4support posts,joist hangers,lag screws,deck boards ...

Get Quotes / Contact Us

Board Foot Calculator | Today's Homeowner

It’s not as confusing as it sounds as long as you remember that a board foot is a measure of volume equal to a square foot one inch thick. So a 1” by 12” a foot long and a 2” by 6” of the same length both equal one board foot.

Get Quotes / Contact Us

How to Build Porch Steps: 13 Steps (with Pictures) - wikiHow

If you want to build porch steps, measure from the top of the porch to the ground, then take the total height and divide it by the riser, which is usually between 6 and 8 inches. For example, divide 35 inches by a 7 inch riser to get 5 steps.

Get Quotes / Contact Us

How to Build a Deck: Design and Layout - Lowe's Home ...

Deck boards are typically 5-1/2 inches wide, so try to plan a deck size that won't leave narrow pieces at the ends. Create your design so that the railings are clear of windows and out-swinging doors.

Get Quotes / Contact Us

How to Build a Porch Swing (with Pictures) - wikiHow

To build a porch swing, start by measuring the area where you want to install your swing to determine how long you should cut your slats. Then, cut 17 slats for the seats, 15 salts for the back, and 4 to 6 back and bottom supports.

Get Quotes / Contact Us