deck ledger board vinyl siding

WPC Decking Related

How to Use Flashing Between Vinyl Siding and a Wood Deck ...

Whether you have wood, vinyl or aluminum siding, you can avoid this by oversizing the ledger board and creating space for water to run off. 1 Make the ledger out of pressure-treated lumber that is ...

Get Quotes / Contact Us

Flashing A Deck Ledger Board Properly - How To

My instinct is to replace the deck and eliminate the ledger altogether (add posts near the wall) and leave a big gap between the end board and new flashing tucked under the siding. I would remove the old siding that was behind the existing ledger to about an inch above the deck surface.

Get Quotes / Contact Us

How to Attach a Ledger to Vinyl Siding | DoItYourself.com

Attach your ledger board to your vinyl siding properly to have a sturdy moisture-proof deck support by following these steps.. Step 1 - Take Measurements. Measure the distance between floor joists, the height of the sill plate and add 1/2 inch for flashing to vent moisture from the ledger.

Get Quotes / Contact Us

HOMETIME HOW TO, Decks - Preparing Siding for Ledger

The ledger board is attached directly to a house wall after the siding has been cut away, and it supports one side of a deck. The first steps in attaching the ledger board are determining where the top of the deck hits the house, where the ledger board goes and where the siding needs to be cut.

Get Quotes / Contact Us

Installing Deck Ledgers Over Exterior Insulation ...

In the long run, cutting into the siding and the exterior foam to install the ledger may be more work than installing the additional footings, posts, and beam needed for a freestanding deck. Mike Guertin is a builder and remodeler in East Greenwich, R.I., and frequent presenter at JLC Live and DeckExpo.

Get Quotes / Contact Us

Flashing a Deck Ledger Board on Vinyl Siding | The Family ...

Snap a chalk line, cut out the siding and tack up the ledger board. Then slip flashing behind the siding, covering the top edge of the ledger. Start by making an outline on the siding where you want to position the ledger board. Make the outline large enough to include space for the deck boards on ...

Get Quotes / Contact Us

How to Attach a Ledger Board to a Vinyl Sided House | Home ...

The ledger board is a horizontal framing member, usually two-by-10 or two-by-12 lumber, that supports one side of a deck and attaches flat to the wall of a house after removing a section of siding.

Get Quotes / Contact Us

Attaching the Ledger Board | Deck Building Project

The ledger board attachment for this home was challenging because it was done after the house was constructed. So you will learn how the siding was removed and two layers of metal waterproof flashing were installed around the board.

Get Quotes / Contact Us

carpentry - How to attach ledger board to under-roof ...

How to attach ledger board to under-roof siding? up vote 1 down vote favorite. ... You mentioned you have wood siding but the texture is of embossed cement board or vinyl Jack May 18 '14 at 4:05. ... How to attach a deck ledger board to a house with no rim joist. 0.

Get Quotes / Contact Us

How to install a proper deck ledger AFTER the fact?

Cut back the siding above the ledger in two places - right at the top of the ledger and 1" above the level of the board that goes over the ledger. Loosen the siding left above the ledger so that you can slip flashing under the paper under the siding.

Get Quotes / Contact Us

How to Attach a Deck Ledger to the House - Fine Homebuilding

No ledger board should be installed with siding between it and the rim joist of the house. “In my opinion,” he says, “a ledger board needs to be attached to the rim with lags or thru bolts. A pair 3 X 3 X 3/16 galvinized bearing plates make great spacers.

Get Quotes / Contact Us

Flashing the ledger board is critical to the integrity of ...

Q. I need to install a deck ledger board against a house with wood lap siding. Soon I’ll be doing the same on a brick home. What is the proper way to install flashing so I don’t get any leaks ...

Get Quotes / Contact Us

DIY Deck Building - ledger attachment part 2 - YouTube

7 videos Play all Deck & Ledger Beam - How to remove & reinstall vinyl siding around it Trevor Brooks Time Lapse: Building a Curved Deck - Duration: 6:50. Deck Builder 37,861 views

Get Quotes / Contact Us

How to Replace Deck Ledger Flashing - HandymanHowto.com

The wood deck ledger board flashing is replaced by tearing off the lap siding and installing new flashing to complete the deck rebuild. This project is continued from How to Replace Wood Deck Boards .

Get Quotes / Contact Us

Is it acceptable to mount a ledger to vinyl siding when ...

If through the siding to the frame of the house it can be however do note that vinyl is designed to "float" on the outside of the home and expand and contract with heat. If you bolt the ledger board to the siding you lock the siding in place there and the siding on either side of the deck at that point likely will buckle in the sun.

Get Quotes / Contact Us

Attaching Ledger to Siding | Decking

Cut Siding and Flash: First, ensure your circular saw is equal to the thickness of the deck, then cut the ledger outline. Slide the flashing underneath the siding 1 inch. Slide the flashing underneath the siding 1 inch.

Get Quotes / Contact Us

Siding To Deck Gap - General Discussion - Contractor Talk

I have flashed my deck ledger board with that 2 sided copper/vinyl stuff. Now i realize that i need to leave a 2" minimum gap between decking and hardiplank siding, which means 2" of gray vinyl flashing will be visible.

Get Quotes / Contact Us

Decks.com. Flashing the Ledger Board

Flashing the Ledger Board If you cut out your siding to install a ledger board, careful steps must be taken to ensure that moisture cannot reach your house. Infiltrating rainwater can travel downward, sideways and even upward, so special flashings must be used.

Get Quotes / Contact Us

Decks.com. Removing the Siding for the Ledger Board

Never install a ledger board over the top of siding no matter what you hear, this can weaken the connection. Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location.

Get Quotes / Contact Us

3 in. x 8 ft. White Galvanized Steel Deck Ledger Wall ...

The Amerimax 8 ft. galvanized deck ledger flashing fits over deck ledger board and behind siding for protection from water damage. Painted galvanized steel features a baked-on factory finish. Use asphalt paper between metal and pressure-treated lumber.

Get Quotes / Contact Us