Triangular panels are common in cross buck passage doors, and raised on both sides to boot! You do not mention the raise profile - hip, cove, ogee, step or whatever, but the procedure is the same. It does not require CNC, just good old woodworker problem solving.
Series 400 plywood panel wood cabinet doors and drawer fronts - for kitchens, bathrooms, closets, and furniture: Series 400 plywood panel mortise & tennon corner doors and corresponding drawer fronts are shown below.
If you're talking veneer core plywood, personally, I would never use it for painted raised panels. MDF is perfectly adequate. If you use a smear of joint compound to fill the cut edge of the raised panel, and properly paint it, it will look just fine.
I want to install raised panel oak doors made from red oak plywood. The thing is … the rails and stiles are made of solid red oak boards. When I cut the panels to insert into the rails, the edges of the panel are a different color.
Plywood > All aspects of solid wood processes apply to plywood with some additions. Apply the same glue with the same thickness of spread to both sides of the panel when laying up, and then ...
Add dimension and shape to your frame-and-panel furniture with raised panels. To form the profile, use a panel-raising bit to rout 3 ⁄ 4 "-thick solid-wood panels. Profile options include ogees, coves, rounded bevels, and chamfered Shaker styles.
NYC's #1 Wood Furniture Store Made in the USA Gothic Furniture is a manufacturer of quality wood furniture since 1969. From the very beginning we have focused on providing beautiful furniture and functional designs that provide unparalleled storage solutions.
I have some glued-up hardwood raised panels that are 3/4-in. thick and 12-in. wide that will fit between rabbeted posts. All of this will be mounted flush against a sheet of 3/4-in. plywood. My choices are to account for expansion by proper spacing of the adjacent posts on each side of the panels ...
From contributor D: It was pretty common to use lumber core ply for raised panels a while ago. I was at a customer's house last week that was built in 1985, and their raised panel doors had an ash lumber core and an oak veneer overlay.
With kids furniture, a solid wood panel would have to be a loose fit, which leaves all the strength of the door to the frame. There would be the movement issues with a solid wood panel, and, having that end grain to deal with, a lot of sanding, and would just suck up paint. ... Another option that's still on the table is a flat (not raised ...
Plywood For Raised Panels. This is a technique that you might try which will yield a raised panel without doing a panel glue up, and saving some cost of solid wood. Using 3/4" hardwood plywood, glue solid stock on all four edges, mitering the corners, and leveling the stock to the panel. The edges can then be profiled.
How to Make Cabinet Doors. Two Methods: ... Most slab doors are made of plywood. Use MDF (medium density fiberboard) on a painted or a covered surface for a wood grain look. 3. Use solid wood for a door when you make a panel door. ... Use a flat (raised panel) door for a quality look.
Other custom touches include the raised-panel treatment on the plywood door panels and the mitered edge-banding on the top and bottom. The top also has a raised lip, or “pencil roll,” applied at the back edge.
3 trendrouting technology Infill Panels The panels can be made from solid timber, veneered plywood or composite board. They can be cut as flat panels or with a traditional raised central area (raised and fielded panels).The
To prove that you don't need expensive cutters to make handsome doors, we made the beautiful raised-panel doors, above, using only three common router bits. Because the panels are hardwood-veneer plywood, they weigh less, cost less, and are more stable than doors made from solid stock.
The Birch Raised Panel Captain's Bed shown above in Queen size has 6 large drawers (three on each side) built-in with metal tracks. It is hand crafted with REAL solid Birch Plywood and Birch Wood Veneer Edging, and Raised Panel drawer fronts.