Roof Flashing Details Index FD01 Interior Roof Drain Detail ... FD05 Roof-Top Equipment Curb Detail FD06 Roof-Top Metal Air Shaft Curb Detail FD07 Roof-Top Wood Air Shaft Curb Detail FD08 Roof Skylight Detail FD09 Roof-Top Chimney Pipe Detail FD10 Roof-Top Plumbing Vent Pipe Detail ... install M60 RubrPoly flashing sheets. Fields Roof Systems ...
Install 2 X 4 Sleepers on pads, directly over joists or perpendicular to existing joists. ... Deck Over A Flat Roof When installed properly as a floating deck, a deck can sit on the roofing membrane. ... When we do install wood decks over the flat roofs, we ensure they are floating, so that there is no punture or penetration of the rubber ...
Jul 26, 2013 Rooftop equipment frequently becomes detached from rooftops during condensers on wood sleepers resting on the roof. (see Figure 6), it is Installing Seismic Restraints for Mechanical Equipment (FEMA 412).
Paul Nichter, a contractor in Islesboro, Maine, responds: I’ve been building wood decks with safe railings over flat EPDM roofs on the rainy coast of Maine for over 15 years without compromising the waterproofing.
I believ that the proper way( that I was trained) is a framed raised wood curb, properly flashed and counter flashed to the roof with a sheet metal cap over the top. This way, in the future, the roof can be re-roofed w/o removing the HVAC equipment.
Hi, Have a house that was designed with a roof top deck, the builder just never put any covering on it and it is jsut the torch down roof material currently Am planning on installing a floating roof top deck - deck boards attached to 2 x 6 sleepers over a torch down roof.
This will be the surface decking is attached to.Roof Top ... over a flat roof of a ... then install “sleepers” or flat ... wood sleepers.Deck on Flat Roof ... Online Service] Roof deck sleeper attachment - JLC-Online Forums
Truss type sleepers for roof top deck . I am building a deck on my low slope roof. You may remember my recent post requesting info on EDPM. While I stripped the roof this last weekend with the help of a friend and covered the deck with 7/16 OSB.
Another thing I see is condensing units setting on roofs, esp restaurants. These are much lighter than the roof top AC units.
Sleepers come in a variety of materials, but only wood sleepers are regularly used in deck building. Concrete and metal sleepers work well for building retaining walls, but these materials are too hard to attach normal deck boards to for a basic deck.
I plan on installing the wood deck on top of wood runners, but I need to protect the EPDM from the runners. (Chaffing damage) My first idea: EPDM (roof) -> EPDM loose scrap (sacrificial layer) -> Closed cell styrofoam (1" cushion) -> wood runner -> wood decking. My second idea: EPDM (roof) -> concrete hardi-backer -> wood runner -> wood deck.
Architects and builders often ask us for advice when installing decking over sleepers. There are many variables that will affect the successful long term installation of decking including proper fastening, proper ventilation, proper material specification and more.
Rooftop Deck Design and Installation Made Easy Over the years we have supplied hardwood decking materials for a fair amount of rooftop decks predominantly in the US. In the past, most of these decks were installed over sleepers.
below the sleepers’ locations. I wanted the tops of the sleepers to be level, so I ripped pressure-treated 2x6s in half so that their bottoms tapered to match the roof pitch. At their thinnest part, the sleepers are 11⁄2 in. deep, so the 2-in. COPYRIGHT 2014 by The Taunton Press, Inc. Copying and distribution of this article is not permitted.
Install the legs into a chem curb which will not crack or split. You should strongly consider a Spray Polyurethane Foam application over your flat asphalt roof when you go to re-roof. That way you keep your good asphalt base with a good fire rating and encapsulate it with SPF which will insulate and protect your asphalt roof.
Truss type sleepers for roof top deck . I am building a deck on my low slope roof. You may remember my recent post requesting info on EDPM. While I stripped the roof this last weekend with the help of a friend and covered the deck with 7/16 OSB. Thankfully the tarps have held up well with all the rain we have been getting.
I'm designing a small wood-framed building right on the waterfront. It will have a flat roof which will used as a deck. I am sloping the joists in one direction at 1/4" per ft with plywood sheathing and a rubber or EPDM membrane over that.
Sleepers for Roof Top Deck Hi, Have a house that was designed with a roof top deck, the builder just never put any covering on it and it is jsut the torch down roof material currently Am planning on installing a floating roof top deck - deck boards attached to 2 x 6 sleepers over a torch down roof.
Designed to withstand extreme rooftop conditions, our products have gone through extensive research, development and testing to make sure they are durable, versatile, reliable, and easy to install. Best of all, our superior-quality products are competitively priced.
I want to use sleepers that run same direction as the roof joists, correct? Then my deck frame joists attach to the sleepers, perpendicular to the joists? My biggest question is with the rubber membrane, piercing it (yikes!), and properly anchoring the deck to the building.